Digital Prosthetic Dentistry Short Course (Theory Part)
Introduction:
In the last two decades Prosthetic Dentistry has had a major shift toward using digital technologies including CAD/CAAM systems. These technologies have reduced the laboratory steps to the extent that one day prostheses are now feasible. Following this wave, different tooth-colored materials only used by CAD/CAM technology, are presented to dentistry to fabricate inlays, onlays, crowns and bridges. At the same time, it is now possible to design and fabricate partial or complete removable dentures with additive CAD/CAM technology. Digital technologies can routinely be used for treatment planning, surgical guide, abutment and prosthesis fabrication in implant dentistry.
So, for an up-to-date dentist the familiarity with digital dentistry is a must do. That’s why Prosthodontics Department of TUMS School of dentistry has planned a short course to share up dated different aspects of digital dentistry. We will be honored if you join us at this event.
Course Director:
Farzaneh Farid DDS
Assistant Professor, Department of Prosthodontics,
School of Dentistry, Tehran University of Medical Sciences
Dr. Eszter Somogyi-Ganss
Assistant Professor in Faculty of Dentistry, University of Toronto, Canada
Dr. Bobby Baig
Associate Professor, Department of Advanced Education in General Dentistry at Eastman Institute for Oral Health, University of Rochester, USA
Mr. Leon Gurgov
A Registered Active Member of the College of Dental Technologists of Ontario (CDTO), Canada
Dr. Farzaneh Farid
Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran
Dr. Hakimeh Siadat
Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran
Dr. Saeed Nokar
Associate Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran
Dr. Azam Sadat Mostafavi
Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran
Dr. Mahmoud Kazemi
Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran
Dr. Faezeh Atri
Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran
Dr. Sareh Habibzade
Associate Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran
Dr. Koroush Sadeghpour
Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran
Dr. Rezvaneh Ghazanfari
Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran
Dr. Ehsan Morshedi
Former Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran
Dr. Leila Payaminia
Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran
Dr. Mahya Hasanzade
Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran
Course Duration:
This 8 hours course will be presented on 22nd and 23rd of May 2021.
Learning Objectives:
-
Becoming familiar with additive and subtractive CAD/CAM technologies and their application in prosthetic dentistry.
-
Becoming familiar with different CAD/CAM treatment options including inlays, onlays, endocrowns and crowns through lectures and videos.
-
Becoming familiar with different materials used in CAD/CAM restorations.
-
Knowing how to prepare teeth for CAD/CAM preparations and its differences with conventional tooth preparation.
-
Knowing how to scan prepared teeth and opposing jaw.
-
Knowing how to design temporary and permanent restorations.
-
Becoming familiar with digital smile design software.
Entrance Requirements:
Applicants should have DDS, BDS or DMD degree and at least 2 years of clinical work as dentist.
Course Venue:
The course is offered online by Prosthodontics Department, School of Dentistry, Tehran University of Medical Sciences, Tehran, Iran.
Certificate:
Certificate of attendance is awarded to attendees who have at least audited 90% of the program. Certificate awarded attendee can directly enroll our hands-on and clinical course. The link of our clinical program is: http://en.tums.ac.ir/en/content/418/digital-prosthodontics
| Title | Time (GMT) |
|---|---|
| Introduction to Digital Dentistry | 04:30 - 05:00 |
| Possible workflow combinations from entirely conventional methods to a completely digital workflow | 05:00 - 05:30 |
| Tooth preparation for CAD/CAM restorations | 05:30 - 06:00 |
| Digital wax up and mock up | 06:00 - 06:30 |
Break | 06:30 - 07:00 |
| Ceramics for CAD/CAM restorations | 07:00 - 07:30 |
| Steps of Fabricating CAD/CAM Restorations: movie | 07:30 - 08:00 |
| Additive Manufacturing Technologies | 08:00 - 08:30 |
| Dynamic Navigation in Implant Dentistry | 08:30 - 09:00 |
Question and Answer | 09:00 - 09:30 |
| Title | Time (GMT) |
|---|---|
| Full Arch Milles CAD/CAM Restorations (Design to Delivery) | 04:30 - 05:30 |
| CAD/CAM Restoration of Endodontically Treated Teeth | 05:30 - 06:00 |
| Cements and Cementation of CAD/CAM Restorations | 06:00 - 06:30 |
Break | 06:30 - 07:00 |
| Digital Workflow for Removable Prosthodontics | 07:00 - 07:30 |
| Digital implant workflow | 07:30 - 08:00 |
| Customized abutments | 08:00 - 08:30 |
Question and Answer | 08:30 - 09:00 |
Day 1: Saturday, 22.05.2021
Introduction to Digital Dentistry
Possible Workflow Combinations from Entirely Conventional Methods to a Completely Digital Workflow
Tooth Preparation for CAD/CAM Restorations
Digital Wax-up and Mock-up
Ceramics for CAD/CAM Restorations
Steps of Fabricating CAD/CAM Restorations
Additive Manufacturing Technologies
Dynamic Navigation in Implant Dentistry
Day 2: Sunday, 23.05.2021
Full Arch Milles CAD/CAM Restorations (Design to Delivery)
CAD/CAM Restoration of Endodontically Treated Teeth
Cements and Cementation of CAD/CAM Restorations
Digital Workflow for Removable Prosthodontics
Digital Implant Workflow
Customized Abutments
