Digital Prosthetic Dentistry Short Course (Theory Part)

Introduction:

In the last two decades Prosthetic Dentistry has had a major shift toward using digital technologies including CAD/CAAM systems. These technologies have reduced the laboratory steps to the extent that one day prostheses are now feasible. Following this wave, different tooth-colored materials only used by CAD/CAM technology, are presented to dentistry to fabricate inlays, onlays, crowns and bridges. At the same time, it is now possible to design and fabricate partial or complete removable dentures with additive CAD/CAM technology. Digital technologies can routinely be used for treatment planning, surgical guide, abutment and prosthesis fabrication in implant dentistry.

So, for an up-to-date dentist the familiarity with digital dentistry is a must do. That’s why Prosthodontics Department of TUMS School of dentistry has planned a short course to share up dated different aspects of digital dentistry. We will be honored if you join us at this event.

Course director:

Farzaneh Farid DDS

Assistant Professor, Department of Prosthodontics,

School of Dentistry, Tehran University of Medical Sciences

Dr. Eszter Somogyi-Ganss

Assistant Professor in Faculty of Dentistry, University of Toronto, Canada

Dr. Bobby Baig

Associate Professor, Department of Advanced Education in General Dentistry at Eastman Institute for Oral Health, University of Rochester, USA

Mr. Leon Gurgov

A Registered Active Member of the College of Dental Technologists of Ontario (CDTO), Canada

Dr. Farzaneh Farid

Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran

Dr. Hakimeh Siadat

Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran

Dr. Saeed Nokar

Associate Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran

Dr. Azam Sadat Mostafavi

Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran

Dr. Mahmoud Kazemi

Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran

Dr. Faezeh Atri

Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran

Dr. Sareh Habibzade

Associate Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran

Dr. Koroush Sadeghpour

Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran

Dr. Rezvaneh Ghazanfari

Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran

Dr. Ehsan Morshedi

Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran

Dr. Leila Payaminia

Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran

Dr. Mahya Hasanzade

Assistant Professor, Department of Prosthodontics, School of Dentistry, TUMS, Iran

Course Duration:

This 8 hours course will be presented on 22nd  and 23rd of May 2021.

 

Learning Objectives:

  • Becoming familiar with additive and subtractive CAD/CAM technologies and their application in prosthetic dentistry.

  • Becoming familiar with different CAD/CAM treatment options including inlays, onlays, endocrowns and crowns through lectures and videos.

  • Becoming familiar with different materials used in CAD/CAM restorations.

  • Knowing how to prepare teeth for CAD/CAM preparations and its differences with conventional tooth preparation.

  • Knowing how to scan prepared teeth and opposing jaw.

  • Knowing how to design temporary and permanent restorations.

  • Becoming familiar with digital smile design software.

 

Entrance Requirements:

Applicants should have DDS, BDS or DMD degree and at least 2 years of clinical work as dentist.

 

Course Venue:

The course is offered online by Prosthodontics Department, School of Dentistry, Tehran University of Medical Sciences, Tehran, Iran.

Certificate:

Certificate of attendance is awarded to attendees who have at least audited 90% of the program. Certificate awarded attendee can directly enroll our hands-on and clinical course. The link of our clinical program is: http://en.tums.ac.ir/en/content/418/digital-prosthodontics


TitleTime (GMT)
Introduction to Digital Dentistry04:30 - 05:00
Possible workflow combinations from entirely conventional methods to a completely digital workflow05:00 - 05:30
Tooth preparation for CAD/CAM restorations05:30 - 06:00
Digital wax up and mock up06:00 - 06:30

Break

06:30 - 07:00
Ceramics for CAD/CAM restorations07:00 - 07:30
Steps of Fabricating CAD/CAM Restorations: movie07:30 - 08:00
Additive Manufacturing Technologies08:00 - 08:30
Dynamic Navigation in Implant Dentistry08:30 - 09:00

Question and Answer

09:00 - 09:30

TitleTime (GMT)
Full Arch Milles CAD/CAM Restorations (Design to Delivery)04:30 - 05:30
CAD/CAM Restoration of Endodontically Treated Teeth05:30 - 06:00
Cements and Cementation of CAD/CAM Restorations06:00 - 06:30

Break

06:30 - 07:00
Digital Workflow for Removable Prosthodontics07:00 - 07:30
Digital implant workflow07:30 - 08:00
Customized abutments08:00 - 08:30

Question and Answer

08:30 - 09:00

Day 1: Saturday, 22.05.2021

 

Introduction to Digital Dentistry

 

Possible Workflow Combinations from Entirely Conventional Methods to a Completely Digital Workflow

 

Tooth Preparation for CAD/CAM Restorations

 

Digital Wax-up and Mock-up

 

Ceramics for CAD/CAM Restorations

 

Steps of Fabricating CAD/CAM Restorations

 

Additive Manufacturing Technologies

 

Dynamic Navigation in Implant Dentistry

 

Day 2: Sunday, 23.05.2021

 

Full Arch Milles CAD/CAM Restorations (Design to Delivery)

 

CAD/CAM Restoration of Endodontically Treated Teeth

 

Cements and Cementation of CAD/CAM Restorations

 

Digital Workflow for Removable Prosthodontics

 

Digital Implant Workflow

 

Customized Abutments

 

Contact Information:                   

Tel: +98-21-88351255, +98-912-3113733

f.farid@yahoo.com

farid@sina.tums.ac.ir